Jump to content

Power Macintosh 5200 Cache/ROM DIMM Replacement

From RetroTechCollection
Power Macintosh 5200 ROM DIMM and U10 clock chip (Apple Service Source)
The logic board with the Cache/ROM DIMM and the clock chip at U10. The inset shows the DIMM layout that Apple's chart says to replace when the centre chip has no sticker.

The Power Macintosh 5200 and Power Macintosh 5300, and the Performa models built on the same logic board, were covered by an Apple Repair Extension Program for system freezes. Apple's program replaced the logic board or the plug-in Cache/ROM DIMM to deal with "known component issues that can cause system freezes"; the checks are the clock chip at U10 on the logic board and the DIMM itself. While the logic board was out, Apple's technicians also fitted new EMI clips and, where an Ethernet card was fitted, a hooked card fence.[1] The program named the Power Macintosh 5200/75 LC and 5300/100 LC and the Performa 5200, 5215 and 5300; the chapter applies to all 52xx and 53xx models except the 5260 and 5280, so it also covers the 5210CD, 5220CD and 5320CD.[2][1] Apple's manual for the Power Macintosh 6200 and 6300 carries the same program for those desktop models.[3]

Symptoms

[edit | edit source]
  • The machine freezes: the menu-bar clock stops and moving the mouse no longer moves the pointer.[1]
  • The machine crashes or hangs intermittently. Apple's chart for that symptom checks the system software (7.5 or later) and software compatibility first, then U10, then the ROM DIMM, then that any Ethernet card is fully seated, and last whether the machine has enough memory for the application.[4]
  • Installing Open Transport 1.1.1 brings up a message that a hardware issue was detected. Apple's explanation is that Open Transport cannot be installed until the Cache/ROM DIMM is replaced.[2]

Freezes with Type 11 errors are a software matter in Apple's view, cured by a clean install of the system software or by updating third-party software.[1] A machine that will not start at all is a different fault; Apple's first cure there is the logic board reset described in Macintosh Performa 5200CD General Maintenance. See also Macintosh Performa 5200CD Troubleshooting.

Check the back of the case first. Apple's technicians fixed an "REA" label (922-2396), or wrote "REA" by hand, above the FCC ID number on every unit repaired under the program.[1]

Tools and parts

[edit | edit source]
Apple part numbers used by the program[1]
Part Apple part number
Logic board, 603/75 MHz, 8-bit sound 661-0931
Logic board, 603/75 MHz, 16-bit sound 661-1008
Logic board, 603e/100 MHz 661-1041
Cache/ROM DIMM 661-1278
EMI clips (pack of 25) 922-2320
Fence for Ethernet 10Base-T card (pack of 2) 922-2329
Fence for Ethernet thin coax card (pack of 2) 922-2330
Fence for Ethernet AAUI card (pack of 2) 922-2441
Ethernet 10Base-T card 661-0888
Ethernet AAUI card 661-0889
  • Apple's diagnostic for the DIMM is the 5XXX/6XXX Tester (version 1.1 in the repair steps), in the Utilities folder of the Service Source 2.5 Companion 2 CD. It reports a suspect logic board or a suspect cache, or that none of the known hardware issues was found. It does not test for the colour-hue fault.[1]
  • A Phillips screwdriver and a hex nut driver, needed only to move the logic board fence to a replacement board.[5]
  • A grounding wrist strap; the logic board is static-sensitive.[1][5]

Procedure

[edit | edit source]

Removing the logic board

[edit | edit source]
  1. Note where the external cables go, switch off, and disconnect the external cables and the power cord. Put on a grounding wrist strap.[1]
  2. Remove the two screws from the I/O door, release the two latches with your fingertips and swing the door up and off.[1]
  3. Swing the logic board handle out from its storage position and pull the logic board out.[5]

Checking U10

[edit | edit source]
  1. Find the clock chip at U10 (see the lead drawing).[1]
  2. Read its part number. If it is not 343S1191 or 343S1121 (ignore any letters after the number), Apple's cure is a new logic board; go to "Fitting a replacement logic board".[1]

Checking the Cache/ROM DIMM

[edit | edit source]
  1. Run the 5XXX/6XXX Tester. Apple's repair steps say not to rely on a visual check to find a faulty DIMM.[1]
  2. The symptom chart gives Apple's visual guide: a DIMM laid out as in the drawing above, with no sticker on the centre chip, is one to replace.[4]

Replacing the Cache/ROM DIMM

[edit | edit source]
Power Macintosh 5200 Cache-ROM DIMM removal (Apple Service Source)
Pulling the Cache/ROM DIMM straight up out of its slot.
  1. Hold each end of the DIMM between thumb and forefinger. Holding it by the chips is acceptable.[1]
  2. Using some force, pull the DIMM straight up out of its slot.[1]
  3. Stand the logic board on edge, with the communications slot end resting on the bench.[1]
  4. Insert the replacement DIMM, with the notches in the DIMM lined up with the pegs in the slot.[1]
  5. Brace the underside of the logic board with your fingertips and press down on the top edge of the DIMM with both thumbs until it snaps into place.[1]

Fitting a replacement logic board

[edit | edit source]

Do this only if U10 failed the check or the Tester reported the logic board.[1]

  1. Remove the two Phillips screws that hold the fence to the solder side of the old board, and the two hex nuts that hold the fence to the SCSI connector. Move the fence to the new board; replacement boards come without one.[1][5]
  2. When refitting the fence, align its flange around the mini-DIN shield first, then swing the rest of the fence into place.[5]
  3. Plug in the logic board battery on the new board.[1]
  4. Move the SIMMs and any expansion cards to the new board. If a double-sided SIMM sits next to a processor heat sink, release the four heat sink tabs from the underside, lift off the heat sink without disturbing the thermal grease, move the SIMM, and refit the heat sinks on both boards.[1]
  5. Leave the Cache/ROM DIMM where it is. Apple's instruction was not to move it to the replacement board, and to return the old board with its DIMM still fitted.[1]

Ethernet card fence

[edit | edit source]
Power Macintosh 5200 Ethernet card end-mount and side-mount fences (Apple Service Source)
End-mount and side-mount fences on Apple's communications-slot Ethernet cards.

Do this if an Apple Ethernet card is in the communications slot, whether or not the logic board was replaced. Without the hooked fence the card can rock out of the slot and drop the network connection intermittently.[1]

  1. Look at the metal fence on the Ethernet card. If it hooks onto the logic board fence, go on to the EMI clips.[1]
  2. If it does not hook on and is riveted to the card, Apple's cure is a new card.[1]
  3. If it does not hook on and is screwed to the card, remove the card, remove the two fence screws and the old fence, and fit the hooked fence.[1]
Power Macintosh 5200 Ethernet card fence hooked to logic board fence (Apple Service Source)
The hook on the card fence engaging the logic board fence as the card goes into the communications slot.
  1. Hook the card fence onto the logic board fence and push the card into the communications slot.[1]

EMI clips

[edit | edit source]

If the original logic board is going back in, Apple replaced its three EMI (ground) clips to prevent damage to the board when expansion boards are installed.[1]

Power Macintosh 5200 logic board EMI clip removal (Apple Service Source)
Squeezing an EMI clip and pushing it out through the board.
  1. With the logic board right side up, squeeze the top of each EMI clip together and push it out through its slot.[1]
Power Macintosh 5200 logic board EMI clip fitting (Apple Service Source)
Fitting a new clip from the underside, open end towards the logic board fence.
  1. Turn the board over. Hold the first new clip with its open end towards the logic board fence.[1]
  2. Push the clip into the slot and press firmly on its base until it snaps into place. Repeat for the other two clips.[1]

Refitting the logic board

[edit | edit source]
  1. Present the logic board at an upward angle to clear the EMI clips, then push it fully home in the enclosure.[6]
  2. Refit the I/O door: align its hinge tabs, slide it up and swing it down until it snaps shut. Reconnect the cables.[5]

Testing

[edit | edit source]
  • Start the machine and check that it boots normally.[1]
  • On a unit with none of the known faults, the 5XXX/6XXX Tester reports that none of the hardware issues covered by the program was found.[1]
  • Freezes that continue are not covered by the program. Apple's remaining advice is to check software compatibility and to follow the user's guide troubleshooting steps.[1]

Revision notes

[edit | edit source]
  • Version B logic boards have a "B" at the end of the serial number printed near the communications port. A version B board that shows a flashing question mark at start-up with a card in the processor-direct or communications slot has a separate check in Apple's chart: if the chip at U6 has no picture of Texas, is 343S0138-a and there is no wire at U27 on the underside, Apple replaces the logic board.[4]
  • The 603/75 MHz board was made with 8-bit or 16-bit sound (661-0931 and 661-1008).[1] Low End Mac's way to tell them apart is capacitor C255: if it is fitted, the board has 8-bit sound.[7]
  • The same program covered colour-hue changes on the display; see Power Macintosh 5200 Internal RGB Cable Replacement.[1]
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.26 1.27 1.28 1.29 1.30 1.31 1.32 1.33 1.34 1.35 1.36 Apple Computer, Service Source: Power Macintosh/Performa 5200 and 5300 (not 5260, 5280) (1997), REA Procedures chapter: Repair Overview for Freezing and Video Color Hue Issues pp. 1–6, System Tester pp. 7–9, Part Numbers pp. 10–11, Before You Begin p. 12 and Repair Procedures pp. 13–29 and 44–46, steps 1–32 and 54–59 (PDF pp. 225–253 and 268–270). Hosted as File:Powermac.perf_5200.5300.pdf; see Power Macintosh/Performa 5200 and 5300 Service Source.
  2. ↑ 2.0 2.1 Apple Computer, Service Source: Power Macintosh/Performa 5200 and 5300, Basics chapter, Open Transport p. 5 (PDF p. 7).
  3. ↑ Apple Computer, Service Source: Performa 6200/6300 Series, REA Procedures chapter, Repair Overview for Freezing and Video Color Hue Issues pp. 2–5 and Repair Procedures pp. 11–15 (PDF pp. 175–178, 184–188). Hosted as File:Performa 6200.6300.pdf; see Performa 6200/6300 Series Service Source.
  4. ↑ 4.0 4.1 4.2 Apple Computer, Service Source: Power Macintosh/Performa 5200 and 5300, Troubleshooting chapter, Symptom Charts/System pp. 3–7, including Figure 1 (PDF pp. 53–57).
  5. ↑ 5.0 5.1 5.2 5.3 5.4 5.5 Apple Computer, Service Source: Power Macintosh/Performa 5200 and 5300, Take Apart chapter: I/O Door pp. 17–19 and Logic Board pp. 20–25 (PDF pp. 100–108).
  6. ↑ Apple Computer, Service Source: Power Macintosh/Performa 5200 and 5300, Additional Procedures chapter, Logic Board Reset pp. 6–7 (PDF pp. 221–222).
  7. ↑ Adam Geller, "Performa 5200", Low End Mac, accessed 2026-10-25: 8-bit or 16-bit sound, identified by whether C255 is present.