Jump to content

Macintosh LC 520 Analog Board Replacement

From RetroTechCollection
Macintosh LC 575 analog board 630-0355 electrolytic capacitors (Marconelly)
An LC 575 analog board, assembly 630-0355, with the electrolytic capacitors marked by value. Photo: Marconelly, TinkerDifferent.

The analog board of the Macintosh LC 520 carries the power supply and the display circuits for the Trinitron tube, and slides out of the bottom of the case once the rear cover is off, the CRT is discharged and its cables are unplugged.[1] The Macintosh LC 550 and Macintosh LC 575 use the same board and procedure, and so do the Performa versions of those machines, the Macintosh Performa 550, Macintosh Performa 560, Macintosh Performa 575, Macintosh Performa 577 and Macintosh Performa 578.[2][3] Owners have found the assembly number 630-0355 on boards from an LC 575, a Performa 550 and a Macintosh TV.[4]

Symptoms

[edit | edit source]

Apple's symptom charts send these faults to a replacement analog board, after the cures listed before it:[5]

  • Clicking, chirping or thumping. The analog board is Apple's first cure, then the logic board.
  • Smoke or a burning smell. Apple's first step is to look over the analog and logic boards for burnt parts.
  • No picture, no sound and no drive activity, once the power cord, the rear switch, another cord and another keyboard have been tried.
  • A single horizontal or vertical line, a flashing or wavy picture, or a high-pitched noise; and any picture fault that the adjustments do not cure. See Macintosh LC 520 Video Adjustment.

A machine that switches itself back on after being shut down has a different cure. Apple's chart says to check for a test jumper at BD11 on the analog board and remove it.[5]

Two TinkerDifferent owners traced a loud squeal or sizzle to the switching transformer in the power supply section, on a Performa 578 and an LC 520. On the LC 520 a recap of the supply section, new parts at the IRFBC40 switching MOSFET, the TDA4605 controller and the CNY17G optocoupler, and reflowing the joints made no difference. Pressing the transformer towards the CRT silenced it, and the LC 520 later began to cut out a few seconds after switching on, which its owner blamed on the transformer and cured with another board. The Performa 578 owner wedged a block against the transformer.[6]

A thin grey horizontal line across the bottom third of the screen is part of the Trinitron design and is not a fault.[5]

Safety

[edit | edit source]

Warning: the analog board works at mains voltage and drives the CRT, which holds a high-voltage charge after the machine is unplugged. Apple's preliminary steps are to remove the rear cover, discharge the CRT and remove the anode cap, and it warns never to use a grounding wrist strap until the CRT has been discharged.[1] See CRT Discharge Procedure.

Pulling the CRT board at an angle can crack the neck of the tube. Apple warns against twisting, bending or forcing it.[1]

Tools and parts

[edit | edit source]
  • Torx screwdriver for the five rear cover screws.[1]
  • Small screwdriver to release the latch on connector BP2.[1]
  • CRT discharge tool; see CRT Discharge Procedure.
  • Grounding wrist strap, used only after the CRT has been discharged.[1]
  • Replacement board, if fitting one: Apple part 661-0192 in the LC 520/550/575 Service Source.[2] Apple's Module Identification guide is reported to give 661-0813 for the LC 520 board and 661-0192 for the LC 550 and LC 575.[4]

Procedure

[edit | edit source]

Removing the rear cover

[edit | edit source]
Macintosh LC 520 rear cover shield centre ground pin (Apple Service Source)
The centre ground pin on the rear cover shield. Apple Computer, Service Source.
  1. Unplug the power cord.
  2. If the rear cover shield has bronze tape on it, remove the tape; Apple says not to refit it. Bend the centre ground pin on the shield back about 1/8 inch (3 mm).[1]
  3. Macintosh LC 520 rear cover removal (Apple Service Source)
    Lifting off the rear cover. Apple Computer, Service Source.
    Remove the five screws with the Torx screwdriver and lift off the rear cover.[1]
  4. Discharge the CRT and remove the anode cap. See CRT Discharge Procedure.[1]
  5. Put on the grounding wrist strap now, not before.[1]

Removing the analog board

[edit | edit source]
Macintosh LC 520 degauss panel ground cables (Apple Service Source)
The two ground cables on the degauss panels. Apple Computer, Service Source.
  1. Disconnect the two ground cables from the degauss panels.[1]
  2. Macintosh LC 520 internal microphone connector (Apple Service Source)
    The internal microphone connector. Apple Computer, Service Source.
    Disconnect the internal microphone connector.[1]
  3. Macintosh LC 520 analog board connectors BP2 BD1 and cable retainer (Apple Service Source)
    Connectors BP2 and BD1 and the cable retainer on the analog board. Apple Computer, Service Source.
    Release the latch on BP2 with a small screwdriver and disconnect the degauss cable.[1]
  4. Disconnect the CRT cable from BD1.[1]
  5. Lift the wires out of the cable retainer.[1]
  6. Macintosh LC 520 CRT board assembly removal (Apple Service Source)
    Pulling the CRT board assembly straight off the neck of the tube. Apple Computer, Service Source.
    Pull the CRT board assembly straight off the neck of the CRT, without twisting or bending it.[1]
  7. Macintosh LC 520 analog board removal (Apple Service Source)
    Sliding out the analog board. Apple Computer, Service Source.
    Slide the analog board out of the chassis.[1]

Fitting a board

[edit | edit source]
  1. If you are fitting a replacement, move the cable retainer from the old board to the new one.[1]
  2. Check both the old and the new board for a test jumper at BD11 and remove it if fitted. Apple says it causes restart problems.[1]
  3. Refit in the reverse order: slide the board in, push the CRT board straight on to the neck of the tube, refit the anode cap, reconnect BD1, BP2, the microphone connector and the two degauss panel ground cables, and route the wires through the cable retainer.[1]
  4. Refit the rear cover and its five screws.[1]

Testing

[edit | edit source]
  • Switch on and check for the start-up chime and a picture.[5]
  • Apple requires the cutoff adjustment whenever the analog board is replaced, followed by white balance; see Macintosh LC 520 Video Adjustment.[1][7]
  • Shut the machine down and check that it stays off. If it restarts on its own, look for the BD11 test jumper.[5]

Revision notes

[edit | edit source]
  • Boards carrying the same assembly number differ in detail. On a Performa 550 board marked revision A5, the 1000 µF 16 V capacitor at CP14 faces the other way to the one in Marconelly's LC 575 photograph; the advice in that thread is to follow the board's own markings and the original part's orientation when recapping.[4]
  • Apple's Module Identification guide lists the Macintosh TV's analog board separately, as 661-0872 with a resistor soldered to the AC connector; owners report using LC 5xx boards in a Macintosh TV.[4]
  • The Color Classic board is a different part, 661-0732; see Macintosh Color Classic Analog Board Replacement.
[edit | edit source]

References

[edit | edit source]
  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 Apple Computer, Macintosh LC 520/550/575 Service Source, Take Apart, Rear Housing pp. 1-3 and Analog Board pp. 6-11 (PDF pp. 38-48). Hosted as File:Lc 520.550.575.pdf; see Macintosh LC 520/550/575 Service Source.
  2. ↑ 2.0 2.1 Apple Computer, Macintosh LC 520/550/575 Service Source, Exploded View (PDF p. 176): Analog Board 661-0192.
  3. ↑ Apple Computer, Performa 500 Series Service Source (Performa 550, 560, 575, 577 and 578), Take Apart, Analog Board pp. 6-11 (PDF pp. 41-46): the same removal steps, without the BD11 jumper note; Exploded View (PDF p. 161): analog board 661-0192. Hosted as File:Performa 500 series.pdf; see Performa 500 Series Service Source.
  4. ↑ 4.0 4.1 4.2 4.3 TinkerDifferent, "Mac LC 575 Analog Board recap guide photos": Marconelly, 4 July 2025 (LC 575 board 630-0355, annotated capacitor photograph); Jerithjdf, 2 and 3 August 2025 (Performa 550 board 630-0355 revision A5 with CP14 the other way round); dougg3, 2 August 2025 (Macintosh TV board 630-0355); kefkafloyd, 6 May 2026 (Apple's Module Identification guide: LC 520 board 661-0813, LC 550 and 575 boards 661-0192, Macintosh TV board 661-0872 with a resistor soldered to the AC connector).
  5. ↑ 5.0 5.1 5.2 5.3 5.4 Apple Computer, Macintosh LC 520/550/575 Service Source, Troubleshooting, Symptom Charts, Video pp. 2-7 and Miscellaneous pp. 16-17 (PDF pp. 20-25 and 34-35).
  6. ↑ TinkerDifferent, "Performa 575 Whining/Squealing noise, analog board", posts by lsi-aigisx86 and Mark_W, 6 to 8 August 2026.
  7. ↑ Apple Computer, Macintosh LC 520/550/575 Service Source, Adjustments, Video pp. 9-10 (PDF pp. 142-143).