Jump to content

Panasonic FS-A1WSX Troubleshooting Guide

From RetroTechCollection

Fault-finding on the Panasonic FS-A1WSX. No schematic or service document for the WSX has been found. The cases below are WSX repairs reported by owners; for circuit-level checks, the Panasonic FS-A1WX Troubleshooting Guide works from the WX's circuit diagrams and traced schematic. The WSX uses the same transformer part number as the WX, but its board has not been confirmed identical.[1][2]

Quick reference

[edit | edit source]
Symptoms and where to start
Symptom First checks Section
Switches itself off and on, or comes back when the case is tapped Solder joints in the supply, transformer connector, power switch Intermittent power
Dead Transformer, then the supply as on the WX No power
Keeps resetting Reset button Constant resets
Drive does not turn or will not read Belt, pulleys, sensor position Drive
Tape loading weak RGB-connector cassette interface Cassette

Intermittent power

[edit | edit source]

In 2023 an imported FS-A1WSX, run from a 120 V to 100 V step-down adapter, kept switching off and on until the top of the case was tapped. After that it would come on, cut out after about ten seconds and come back. The owner had already replaced the mains cable and the drive belt, and reflowing the power switch's joints made no difference.[3]

Forum members' suggestions, in the order they were made:[3]

  1. sd_snatcher: broken solder joints or bad capacitors in the supply, the internal connector to the transformer, or a faulty power switch. He added that this is not a common fault on Panasonic MSX2+ and turbo R machines.
  2. NYYRIKKI: if the power lamp reacts to tapping, the fault is in the supply; measure the voltages.
  3. maxis: a typical sign of a dry joint; inspect every joint under magnification and resolder any that are cracked or that move when the component is wiggled.
  4. Pencioner: the contacts inside the power switch itself can oxidise and make the switch run hot.
  5. Wierzbowsky: inspect both sides of the board, starting with the AC power connector on the main board and the AC-DC section.

The thread does not record the final cause.[3]

No power

[edit | edit source]
Panasonic FS-A1WX power supply circuit (figure 8)
The FS-A1WX power unit. No WSX circuit diagram has been found.

A failed internal transformer has been reported on a WSX.[1] Check the transformer's output at the four-pin connector against the WX figures in the maintenance guide, then work through the supply as described for the WX.[4]

Constant resets

[edit | edit source]

On an FS-A1WX, a reset button that stuck down made the machine reset continuously until it was freed.[3] Check the reset button first on a WSX that keeps resetting.

Drive

[edit | edit source]
  • The drive is a belt-driven Matsushita EME-213MA.[5] A drive that does not turn may have a perished belt; the replacement procedure is in the maintenance guide.
  • Melted rubber left on the pulleys stops a new belt reading discs; clean the pulleys with isopropyl alcohol.[5]
  • After a belt change, check that the sensor beside the belt is back in its original position.[5][6]
  • Test the drive with CALL FORMAT on a spare disc.[5]

Cassette

[edit | edit source]

The WSX has no separate data recorder socket: tape loading and saving go through the RGB connector with a special cable, and the volume is much lower than on a normal tape interface.[6] Weak tape signals are therefore expected on this machine.

Clock

[edit | edit source]

If the time is lost at power-off, check the backup cells. The MSX Resource Center advises against alkaline cells because they leak.[6]

References

[edit | edit source]
  1. ↑ 1.0 1.1 Help with the FS A1WSX internal transformer, July 2004—link(accessed 2026-10-21) Niles: the WSX's internal transformer had failed; it is marked "DDT5U7J02Z-W", and its connector to the main board has four pins. NYYRIKKI: probably the same transformer as in the A1WX (round, about 11 W, he thought); he had his rewound for 220 V by a local repair shop and later used it in an A1ST, which originally has a different transformer and connector; the usual problems of the Panasonic FS series are the drive belt, the power supply and a worn keyboard membrane. Sonic_aka_T: his FS-A1GT's three-pin CN1 measured 19.2 V AC from pin 1 to each of pins 2 and 3, off load, on 120 V mains.
  2. ↑ BABAX, Panasonic MSX2+ FS-A1WX Schematic, revision 04a, 9 August 2014, traced from a board marked DFUP0250ZAU1a (serial 8KCKB01501), with parts list "FS-A1WX パーツリスト PARTS LIST", 5 August 2014, revision 02. Parts list: IC1 CXA1145M; IC2 TC8566AF; IC3 M60014-0140FP (the drawing labels it "FX/WX gate array"); IC4 T9769A or B; IC5 YM2413; IC6 LM324; IC7 MC34063; IC10 MN1280R; IC11 to IC14, IC22 and IC23 MB81464-12; IC17 and IC18 MB834000; IC19 and IC20 MB8464-15L; IC21 and IC24 81C4256 shown in brackets as unfitted; IC28 79L12; IC29 78L12; Q11 2SA1598; D8 SB540; X1 16.00 MHz; X2 32.768 kHz; X4 21.47727 MHz; T1 transformer DDT5U7J02Z-W; V1 battery 1.5 V × 2; RY1 relay SZ-5; CN1 power in, CN6 RGB (8-pin DIN), CN7 cassette (8-pin DIN), CN13 drive. The drawing labels IC8 V9958 "MSX-VIDEO II"; the parts list gives "V9938 E-VDP-II". The list notes that ROMs and transistors can differ between production lots. Community reverse-engineered drawing, not a Panasonic document. Hosted as File:Panasonic FS-A1WX schematic and parts list (BABAX, Rev 04a).pdf.
  3. ↑ 3.0 3.1 3.2 3.3 FS-A1WSX powering off/resetting until I tap the machine, December 2023 to January 2024—link(accessed 2026-10-21) pawlicker: an imported FS-A1WSX, run from a 120 V to 100 V step-down adapter, switched itself off and on until the top of the case was tapped; reflowing the power switch did not help. sd_snatcher: not a common fault on these machines; suspect broken solder joints or bad capacitors in the supply, the internal connector to the transformer, or the power switch; Panasonic, Sony and Sanyo MSX machines run on about 127 V 60 Hz without a step-down transformer, unlike Toshiba ones. NYYRIKKI: if the power LED reacts to tapping, it is the supply; measure the voltages. maxis: a typical sign of a dry joint; inspect every joint with magnification. Pencioner: oxidised contacts inside the switch itself can cause it and make the switch hot. Wierzbowsky: inspect the board from both sides, starting with the AC power connector and the AC-DC section. MSXcri: his FS-A1WX's reset button sometimes stuck down, making the machine reset continuously until the button was freed.
  4. ↑ FS-A1FX/WX/WSX memory area PCB repair, March 2005—link(accessed 2026-10-21) Alexandre_Taito (Alexandre Souza): an FS-A1FX board in a WSX case had most of the tracks in the user RAM area torn away by an attempted 64 KB to 256 KB upgrade, and he rebuilt them with fine wire; on the four-pin transformer connector, pins 1 and 3 pass through diodes and join, and pin 4 feeds two diodes, one to a 78L12 and one, reversed, to a 79L12; running on a 24-0-24 V transformer, the internal supply and especially the main switching transistor got too hot. 22 March 2005, quoting DaBest's measurement of a WX: pin 1 12 V, pin 2 ground, pin 3 12 V, pin 4 17 V.
  5. ↑ 5.0 5.1 5.2 5.3 Panasonic「FS-A1WSX」ゴムベルト交換, 29 November 2015—link(accessed 2026-10-21) The FS-A1WSX's drive is a belt-driven Matsushita EME-213MA. Procedure: remove seven Phillips screws from the underside and lift off the top, unplugging two connectors; remove the four screws holding the drive base and unplug the flat cable; remove the drive's four screws (the screws on the black plate can stay); remove the screw and the white plastic part, and photograph the position of the sensor mounted with the board beside it first, because it is easy to refit wrongly; change the belt; reassemble and test with CALL FORMAT. Melted rubber was stuck to every pulley; left in place, it stops a new belt reading discs; isopropyl alcohol removes it cleanly. The author used a Daiso "D-009" hair band (small size) as a substitute belt, and laid clear tape in the guide groove under the black pulley to stop the belt slipping into the gap between the pulley and the metal frame.
  6. ↑ 6.0 6.1 6.2 Panasonic FS-A1WSX, MSX Resource Center wiki, 14 August 2026—link(accessed 2026-10-21) Community page: released October 1989 in Japan at ¥69,800 as the successor of the FS-A1WX; the cassette port is combined with the RGB connector (loading and saving work with a special cable, at a much lower volume than a normal tape interface); S-video output added; colour printing with the Panasonic FS-PC1 printer; 64 KB RAM in slot 3-0 and 16 KB SRAM; 128 KB VRAM; Yamaha V9958; PSG and MSX-MUSIC; Toshiba T9769 model B or C and a Mitsubishi gate array given as M50014; firmware bypassed only with the front switch, not the DEL key; RAM can be raised to 256 KB with a little soldering and to 512 KB with a more complicated modification; drive belt rubber, 0.3 mm thick, 58 mm diameter, 3 mm wide, sold as Panasonic FW-U1P501J; the gallery shows the EME213MA drive, with the caption that its alignment sensor must be moved during a belt change; connections RF, audio and composite video, RGB output and data recorder port, S-video, printer, two general-purpose ports, two cartridge slots, mains plug for AC 100 V ±10 %, 50/60 Hz; recommended backup batteries lithium or Eneloop, alkaline advised against "because they leak one day or another".



Retrieved from "https://retrotechwiki.com/index.php?title=Panasonic_FS-A1WSX_Troubleshooting_Guide&oldid=28394"